Assembly and adjustments (continued)
Advertising
1. Open the upper and lower doors. Rotate the wheel forward by hand, and observe the
Emerson 10-4200R, Auto Feed Unit, 7 and 10, Band Saw, Operations and Parts Manual Emerson on Amazon.com.FREE. shipping on qualifying offers. Industrial Machinery Manuals is Proud to Offer 1 Digitally Enhanced Quality Bound Copy Of A: Emerson 10-4200R. Apr 12, 2011 This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register. By continuing to use this site, you are consenting to our use of cookies. Dayton Band Saw 4YG30A View manual. We recommend. P CP Grob 4V500 Guide Kit Grob 4V Bandsaw. Guide Kit fits all model Grob 4V Band Saws from 18″ to 24″ diameter wheel sizes Kit contains. View details. BSP GS DA 100 V DoAll 1″ Horz Guide Set. This Kit will fit the following Machines: C-58, C-70, C-206A, C-305A, C-916A, C-80.
position of the blade on the wheel. It should be in the center of the wheel.
2. Loosen the lock knob (Figure 7) and make adjustment with tracking knob (Figure 7) while
rotating wheel by hand.
3. Tightening the tracking knob slightly will move the blade so it tracks towards the rear of
machine. Loosening the tracking knob slightly will cause the blade to track toward the front
of the machine.
4. After blade is tracking in the center of the wheel, tighten the lock knob (Figure 7).
Blade guide adjustment
(Figure 8,9& 10)
https://intensiveshared.weebly.com/unistall-little-snitch.html.
The upper blade guide assembly (3, Figure 8) should be adjusted to just above the material being cut. To adjust: loosenthe lock knob (2, Figure 8) and raise or lower the upper blade guide assembly (3, Figure 8) by turning the height adjustment knob (1, Figure 8). The blade guide assembly consists of two roller guides (bearings) positioned on each side of the blade to provide blade stability. A third guide (thrust bearing) is positioned behind the blade to provide blade support. There are two blade guide assemblies - an upper assembly and a lower assembly (see Figure 11). Adjustments are performed in the same manner for each assembly. Each assembly must be adjusted in turn using the adjustment procedures outlined below. Thrust Bearing Adjustment (Figure 9)
WARNING:Disconnect machine from the
power source! Never make adjustments with the machine running! Failure to comply may
cause serious injury!
1. Disconnect machine from power source. Note: Blade must already be tensioned and tracking properly. 2. For the upper thrust bearing, loosen thumbscrew (B).
For the lower blade guide, loosen setscrew (B) with
the 3mm hex wrench provided.
3. Slide the adjustment shaft (C) so the blade is
positioned in the middle of the thrust bearing (A).
The thrust bearing (A) is mounted on a concentric shaft
(C). When the shaft is rotated, the relative position of the bearing to the back of the blade can be changed. 4. Rotate the adjustment shaft (C) so the thrust bearing
Download epanet 2.0 for mac. (A) just clears the back of the saw blade.
5. Tighten thumbscrew/setscrew (B).
2
3
User Bjorn Toulouse Library Emerson 2520 Bandsaw 2520 Manual Instructions
Figure 9
Lower blade guide assembly
Upper blade guide assembly
User Bjorn Toulouse Library Emerson 2520 Bandsaw 2520 Manual Pdf
1
User Bjorn Toulouse Library Emerson 2520 Bandsaw 2520 Manual 2016User Bjorn Toulouse Library Emerson 2520 Bandsaw 2520 Manual 2017
Advertising
Popular Brands
Popular manuals
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |